Automatically Setting Up Programme
SETUP Auto Tuning
Automatically tunes the programmes.
- Select Country where the TV is used. Programme settings change depending on the country you choose. (This feature is available in certain countries only.)
- Initiate Auto Tuning.
- Set Auto Tuning following screen instructions.
If Input Source is not connected properly, programme registration may not work.
Auto Tuning only finds programmes that are currently broadcasting.
If
Lock System is turned on, a pop-up window will appear asking for password.
Cable DTV Setting option
When searching for programmes using FULL setting it can take a long time.
The following values are needed in order to search all available programmes quickly and correctly. The commonly used values are provided as “default”.
- Frequency
Enter a user-defined frequency. - Symbol rate
Speed at which a device such as modem sends symbols to a programme. - Modulation
Loading of audio or video signals onto carrier. - Network ID
Unique identifier allocated for each user. - Start Frequency
Enter a user-defined start frequency range. - End Frequency
Enter a user-defined end frequency range.
Satellite Setting Option
- Satellite
Select your desired Satellite. - LNB Frequency
[This feature is available in certain countries only.]
Select one value from 9750 / 10600, 9750 / 10750, 9750, 10600,10750, 5150, MDU1, MDU2, MDU3, MDU4, MDU5.
If you select 9750 / 10600, 9750 / 10750(MHz), 22kHz Tone is disabled. If you cannot find the LNB frequency value from the list, select User and manually enter the frequency. - Transponder
Select the transponder you want to tune. - 22kHz Tone
When using 22kHz Tone switch, select A or B. If you use 22kHz Tone, Unicable and Motor Type are disabled. - LNB Power
To enable the power supply for the LNB, select On. If you select Off, Motor Type is disabled. - DiSEqC
When using DiSEqC, select one option from A~D / ToneA~B. If you use DiSEqC, Unicable and Motor Type are disabled. - Unicable Setting
Select On to use Unicable and set the Unicable in the Unicable Setting menu. When Unicable is enabled, 22kHz Tone, DiSEqC, Motor Type are disabled. - Motor Type
Select Motor Type to use Motor and set the Motor in the Motor Setting menu. When Motor is enabled, 22kHz Tone, DiSEqC, Unicable are disabled.
If you set satellite to others, you must add a transponder using Manual Tuning or Transponder Edit.
When selecting 22kHz Tone and DiSEqC, you must connect them in the same position as displayed on the OSD.
If you delete a Satellite, all programmes stored in the Satellite are deleted.
Motor Setting Option
- DiSEqC 1.2
Control motor to change satellite dish position. Drive Direction
Select the direction in which you want to move the motor.
Drive Mode
Two modes are available : Step and Continuous.
- Step
The motor moves based on the value you enter (from 1 to 128). - Continuous
The motor moves continuously until you press the Stop.
Select the Test TP you want to tune.
Set Limit
Set the motor movement to east or west to have the motor move only within the direction set.
- On
You can limit the movement to the current direction by selecting the West / East. - Off
You can cancel the limit you set.
You can move the motor to Zero.
Store
You can save the motor’s current direction. - Step
- USALS
Set your current location (Longitude / Latitude).
Cable DTV Setting
SETUP Cable DTV Setting
- Service Operator
Set Service Operator.
When changing Service Operator, the existing saved programmes are deleted and Auto Tuning runs. - Channel Auto Update
- On
You can update information for all the programmes that can be updated, including the programme currently being watched. - Off
You can only update information for the programme currently being watched.
- On
The range that a user can select from the Service Operator menu differs depending on number of Service Operator supported by each country.
If number of supported Service Operator for each country is 1, corresponding function becomes inactive.
Satellite Setting
SETUP Satellite Setting
You can add / delete / set the satellite you want.
Transponder Edit
[If the programme mode is set to Satellite]
SETUP Transponder Edit
You can add / modify / delete a transponder.
To use Manual Tuning
SETUP Manual Tuning
Adjusts programmes manually and saves the results.
For digital broadcasting, signal strength and signal quality can be checked.
For digital broadcasting, signal strength and signal quality can be checked.
[This feature is available on certain models only.]
You can also adjust the frequency(KHz) and bandwidth.
You can also adjust the frequency(KHz) and bandwidth.
To edit programmes
SETUP Programme Edit
Edits the saved programmes.
Set as favourite programme, block/unblock programme, skip programme etc. of the selected programme.
Set as favourite programme, block/unblock programme, skip programme etc. of the selected programme.