Cleaning the Lint Filters

Clean the lint filters in the proper way referring to the following instructions. Failure to do so, the lint that is accumulated on the heat exchanger may not be cleaned properly.Unload all of the laundries from the appliance before pull out the lint filters.Put the lint filters back in place after cleaning. If the lint filters are not in the appliance, you can not operate the appliance.when cleaning the filters, the lint should be thrown in the trash and not washed through the drain in order to avoid spreading microplastics in the used water system.Inner FilterAlways clean the inner filter before and after use.Outer FilterClean the outer filter after drying 10 times or when the lint is accumulated into the outer filter.A chime will sound and the K indicator will blink when the lint has accumulated.Pull out the inner filter from the outer filter and then open the inner filter.Open the filter by unfolding it in the direction of the arrows.Clean large cluster of lint first, then clean the residual lint by hand or using a vacuum cleaner.Dry the filter completely if the filter is moist. Failure to do so, odour may occur in the appliance.Dispose of the used tissue in the trash.Close the filter completely by pushing down its center.Ensure the left and right side of the inner filter is closed properly.Insert the inner filter into the outer filter.Remove the dust or lint around the filter inlet.When the lint drops into the filter inlet, it may cause less efficient drying performance and increase of drying time.Pull out the outer filter.Remove the inner filter.Grab the top edge of the outer filter and spread open.Clean the residual lint filter by hand or using a vacuum cleaner.Dry the filter completely if the filter is moist. Failure to do so, odour may occur in the appliance.Dispose of the used tissue in the trash.Close them, and reinsert the both lint filters.Do not load or remove any clothes when the lint filter is not in a place. The clothes can drop into the filter inlet and it may cause the appliance to malfunction.

Wiping the Moisture Sensor

This device senses the moisture level of the clothes during operation, which means it must be cleaned once every six months to remove any build-up of lime scale on the surface of the sensor.Wipe the sensors inside the drum.Do not wipe the moisture sensor with abrasive materials. Always clean the sensor with a dry rough acrylic sponge.

Using Drum Clean Feature

With time and use, the appliance may form unpleasant odours that leave your clothes smelling after drying. Using this cleaning function once a month (or after drying 30 times) helps to reduce the unpleasant odours from the appliance.Remove all of the clothes from the appliance.Turn on the appliance.Press the Drum Care button.Hold the Start/Pause button.This function operates for about 3 hours.Open the dryer's door to provide the appliance with enough air circulation for exhausting any remaining odours.For safety reasons, do not allow children or animals to enter the appliance. It may cause damage or injury.

Using Condenser Clean Feature

The appliance washes lint, which builds up onto the surface of the condenser, automatically using water that is condensed from the clothes during operation. Using this cleaning function once a month (or after drying 30 times) helps to wash the lint.Remove all of the clothes from the appliance.Open the dryer's door and pull out both inner and outer filter.Pour 1 litre of clean water slowly into the entrance.Do not pour the water quickly as it will spill out.Pouring more that 1.5 litres of water into the compartment will cause water to leak back out.Reinsert both inner and outer filter and close the dryer's door.Turn on the appliance.Press the Condenser Care button.Hold the Start/Pause button to start the cleaning of the condenser.The cleaning of the condenser proceeds for 1 hour.Open the dryer's door to provide the appliance with enough air circulation for more thorough drying of the tub after the cleaning has ended.For safety reasons, do not allow children or animals to enter the appliance. It may cause damage or injury.

Thawing out the Appliance

Open the dryer's door and pull out both inner and outer filter.Pour 1 litre of hot water at 60 ℃ into the lint filter compartment and then reinsert the both lint filters.Pouring more that 1.5 litres of water into the compartment will cause water to leak back out.Pouring hot water over 60 ℃ will cause malfunctions to the appliance or burn.Turn on the appliance and operate the Cotton programme about for 30 seconds. Then wait about 30 minutes.Operate the Cotton programme again. Check if the OE message will appear within 10 minutes after operating the appliance.When the OE message appears go to step 2 and repeat procedure.Nothing appears on the display when the thawing is done.Dry the clothes as usual.