Using the Steam Mop Nozzle

Press the Power button. You can use the only mop mode and not turn on the dust suction function.

By default, the dust suction function will be off in normal mop mode or steam mode.

Press the right Move 4 button to turn on the dust suction function.
Press the left Move 3 button to turn off the dust suction function when it's on.
Press the Move 3 4 buttons to adjust the suction power when the dust suction function is on. The current suction power is displayed on the status display.

Steam mop mode	Insert the battery pocket and onto the battery into the steam mop nozzle and turn on the power to the main unit. Set the steam nozzle to steam mop mode in the setting mode.
Warm water mode	Insert the battery pocket and onto the battery into the steam mop nozzle and turn on the power to the main unit. Set the steam nozzle to warm water mode in the setting mode.
Normal mop mode	Turn on the power to the main unit without inserting the battery pocket or the battery into the steam mop nozzle. Set the steam nozzle to normal mop mode in the setting mode. The battery in the battery pocket will only be used when the steam mode operation is on.

Caution

Do not assemble or disassemble the nozzle while the appliance is turned on. Doing so may result in injury.
Do not use on PVC or PU mats for infants or children. Hot steam may damage the mat or cause the mop attachment plate to not rotate smoothly, resulting in overheating the motor.
Do not force the steam mop nozzle onto the floor or apply any force to it. Doing so may damage the floor and/or the product.
Do not step on the steam mop nozzle. Doing so may damage the product.

Press the PUSH button a to remove the water tank from the mop nozzle.
Open the water inlet cap b on the side of the water tank and fill the tank with water using the measuring cup c.
- Do not put any liquid other than purified water and hot water in the water tank.
- After filling the water tank with water, wipe any remaining water from the surface of the water tank to prevent any remaining from falling onto the floor.
Close the water inlet cap tightly.
- If the water inlet cap is not closed properly, water may leak.
Attach the water tank to the mop nozzle again.
- Insert the 2 tabs d at the front of the water tank into the slots e on the top of the mop nozzle. Press down at the centre f to lock the tank in place.

Warning

Be sure to attach the mop pads after turning off the power. Failure to do so may cause the mop attachment plate to rotate and may result in injury.

Caution

Do not let the appliance stand on the floor while the wet mop pads are attached. Doing so may result in damage or swelling to wood flooring.

Wet both sides of the mop pads with water then squeeze out any excess water before attaching the pads.
- Do not attach pads while they are dripping wet.
- Use wet mop pads instead of dry mop pads when using steam mode
Place the mop nozzle upside down on the floor.
Align and attach the centre of the mop pad with the centre of the mop attachment plate.
- Attach the Velcro on the mop pad to the mop plate. Attaching the mop pad upside down or improperly may affect the cleaning results.
Attach the mop nozzle to the appliance.

Warning

To avoid injury, do not attach the mop pad while the mop attachment plate is rotating.

Caution

Do not let the appliance stand on the floor while the wet mop pads are attached. Doing so may result in damage or swelling to wood flooring.

The amount of water sprayed automatically can be adjusted in three levels through the Adjust the Amount of Water Supply setting in the setting mode.

When using the steam mode, a constant amount of water is supplied.

Level 1: Use this setting to supply a small amount of water for cleaning wood or other flooring that can be damaged by too much water.

Level 2: Use this setting to clean ingrained dirt or supply a large amount of water.

None: Use this to stop the supply of water so you can go over areas that are already wet.

When using the steam mode, a constant amount of water is supplied regardless of the operation of the water adjustment buttons.
Insert the water tank filled with water into the steam mop nozzle, attach the mop pads soaked in water, and then insert the battery pocket.

Insert the battery pocket b into the steam mop nozzle c, and insert the fully charged spare battery a into the battery pocket b. Push the battery pocket and the battery all the way in until a click is heard.
Insert the steam mop nozzle into the extension pipe and connect it to the product body. When you press the Power button d on the product body, the steam mode will be turned on and preheating will begin.
- During preheating, the nozzle front LED will blink.
- When you turn on steam mode, the steam generator will be preheated for about 40 seconds and then steam will be sprayed. Begin cleaning when the red battery pocket LED turns on. It's normal for steam to not be emitted from the mop pads as the steam can be dissipated by the floor or the pads.
- After steam is sprayed, it takes about 80 seconds for the mop pads to be heated as below.
  - Steam mop mode: about 60 7
  - Warm water mode: about 50 7
*1
This is the test result measured by attaching the wet mop pads on the steam mop nozzle. The surface temperature of the wet mop pads may vary depending on the environment, measuring location, and measuring equipment.

When cleaning is finished, press the Power button on the product body to turn the product off.
The battery pocket does not have a charging function. Separate the battery from the battery pocket and charge it using the charging station.
Press the release button and separate the extension pipe.
Hang the nozzle on the nozzle hook.

Separate the battery pocket by pressing the PUSH button on the bottom of the battery pocket and sliding it upward off the mop nozzle.

Warning

Do not separate the water tank from the steam mop nozzle or add water to the water tank while the power is on or cleaning in progress. Doing so may result in burns due to steam or hot water.
Never turn the steam mop nozzle upside down, tilt or shake it while the power is on, while cleaning, or immediately after cleaning is finished. Steam or hot water may leak and cause burns.
After cleaning, separate the mop pads from the steam mop nozzle after letting it cool sufficiently. Touching the steam mop nozzle or the mop pads before they are sufficiently cooled may result in burns.
After steam cleaning, hot steam may become water droplets and hot water may flow from the inlet. After cooling the product sufficiently, clean the nozzle and store the product in the charging station.

Note

If there is no water in the water tank, no steam will be produced. Fill the water tank with water and attach the pre wet mop pads before use.
When the steam mop nozzle is turned on and left in place, no steam will come out in order to prevent damage to the floor.
When cleaning with steam, set the steam mop nozzle in the setting mode to use Normal mop mode.
The steam cools and can condense into water droplets, which can drip when the nozzle is turned upside down or stored. This is not a leak, so use it with confidence.