Before Installing
Moving or installation of the appliance requires two or more people. Failure to follow these instructions may result in injury.Store and install the appliance where it will not be exposed to temperatures below freezing or exposed to outdoor weather conditions. Failure to follow this warning can cause product or part failure, serious injury, fire, electric shock, or death.Properly ground the washer to conform with all governing codes and ordinances. Failure to follow this warning can cause serious injury, fire, electric shock, or death.To reduce the risk of electric shock, do not install the appliance in humid spaces. Failure to follow this warning can cause serious injury, fire, electric shock, or death.To ensure proper airflow, do not block the large opening on the bottom of the washer with carpeting or other materials.Do not remove the ground prong from the power cord. Do not use an adapter or extension cord. Plug into a grounded 3-prong outlet. Failure to follow this warning can cause serious injury, fire, electric shock, or death.Certain internal parts are intentionally not grounded and may present a risk of electric shock only during servicing. Service personnel - Do not contact the following parts while the appliance is energized: pump, motor, noise filter cover, protective cover and heater (on applicable models).
Choosing the Proper Location
Check the following requirements for the install location before installing the washer.Allow for sufficient space between the walls and the washer for installation.Make sure that the floor is clean, dry and free of dust, dirt, water and oil so the leveling feet cannot slide easily. Leveling feet that can move or slide on the floor can contribute to excess vibration and noise.If the floor has too much flex, reinforce it to make it more rigid. If the floor is not solid, it may cause severe vibration and noise.
Unpacking and Removing Shipping Material
Remove all shipping materials from the washer for proper operation and inspect it for shipping damage.Failure to remove shipping materials can cause excessive noise and vibration.
Connecting the Water Inlet Hoses
To avoid the risk of costly water damage, purchase and install new inlet hoses when installing the washer.Do not overtighten the hoses or cross-thread the hose fittings. Overtightening or cross-threading can damage the valves or couplings, resulting in leaking and property damage.Do not reuse old hoses. Use only new hoses when installing the washer. Old hoses could leak or burst causing flooding and property damage. Contact an LG Customer Information Center for assistance in buying hoses.Periodically check the hoses for cracks, leaks, and wear, and replace the hoses every five years.Do not stretch the water hoses intentionally, and make sure that they are not pinched, crushed or kinked by other objects.Water supply pressure must be between 20 psi and 120 psi (138 - 827 kPa). If the water supply pressure is more than 120 psi, a pressure reducing valve must be installed.Your hot water heater should be set to deliver water at 120 - 135°F (48 - 57°C) to allow the washer to properly control wash temperatures.If your water supply contains a lot of debris, a whole home water filter may help to remove the debris from the water before it reaches the washer inlets.Do not store or install the washer in a location subject to freezing temperatures. Damage to the water inlet hoses and internal mechanisms of the washer can result. If the washer was exposed to freezing temperatures prior to installation, allow it to stand at room temperature for several hours before use and check for leaks prior to operation.Do not use flood-preventing hoses with auto shutoff devices. The devices can be tripped during fill and prevent the washer from filling properly.
Connecting the Drain Hose
Connect the drain hose to either a standpipe or laundry tub.The drain hose should always be properly secured. Failure to properly secure the drain hose can result in flooding and property damage.The drain must be installed in accordance with any applicable local codes and regulations.Make sure that the drain hose is not stretched, pinched, crushed, or kinked.The end of the drain hose should be located a minimum of 29.5 inches (75 cm) and a maximum of 96 inches (244 cm) above the bottom of the washer.For best results, locate the end of the drain hose no higher than 66 inches (168 cm) above the bottom of the washer. As the drain outlet is raised beyond 66 inches (168 cm), the drain function will be increasingly affected.Never create an airtight seal between the hose and the drain with tape or other means. If no air gap is present, water can be siphoned out of the tub resulting in poor wash/rinse performance or clothing damage.
Leveling the Washer
The tub of the washer spins at very high speeds. To minimize vibration, noise, and unwanted movement, the floor must be a solid, level surface.Using the washer without leveling it may cause excess vibration and noise, leading to a washer malfunction.Adjust the leveling feet only as far as necessary to level the washer. Extending the leveling feet more than necessary can cause the washer to vibrate.Before installing the washer, make sure that the floor is clean, dry and free of dust, dirt, water and oil so the washer feet cannot slide easily. Feet that move or slide on the floor can contribute to excessive vibration and noise.
Final Installation Check