Cleaning the Tub

Over time, residue may build up in the tub, leading to mildew or a musty odor. Run the Tub Clean cycle monthly to remove residue and prevent odor.Make sure to run the Tub Clean cycle only when the tub is empty. Never load laundry while using this cycle. The laundry may be damaged or contaminated with cleaning products. Run the cycle more often under heavy use conditions or if odor is already present.If mildew or musty smell already exists, run this cycle once a week for three consecutive weeks.Remove any clothing from the tub.Adding cleaning agents.CleanerInstructionsTub cleanerFollow manufacturer’s recommendations.Lime scale removerLiquid chlorine bleachAdd to main wash liquid detergent dispenser.Powdered cleanerFollow manufacturer’s recommendations.Cleaning tabletsPlace directly into the washer tub.For other tub cleaning products, follow the cleaner manufacturer’s instructions and recommendations.Do not exceed the maximum fill line when adding bleach or powdered cleaners. Powdered cleaners may remain in the tub after cleaning.Close the lid and press the Power button to turn on the washer.Turn the knob or press the cycle buttons to select the Tub Clean cycle then press the Start/Pause button to begin the cycle.After the cycle ends, open the lid and allow the tub interior to dry completely.Make sure children and pets do not climb into the tub. Engage the Child Lock feature if needed to prevent children from accidentally starting a wash cycle.If you use a descaler or tub cleaner during the TUB CLEAN cycle, use the RINSE+SPIN option to rinse the washer tub before running your next wash cycle.

Removing Mineral Buildup

In areas with hard water, mineral scale can form on internal components of the washer. Periodically clean the mineral buildup on the internal components to extend the lifespan of the washer. Use of a water softener is recommended in areas with hard water.Use a descaler to remove visible mineral buildup on the washer tub.After descaling, always run the Tub Clean cycle before washing clothing.Mineral scale and other spots may be removed from the stainless steel tub using a soft cloth soaked in stainless steel cleaner.Do not use steel wool or abrasive cleaners.

Leaving the Lid Open

After you finish using the washer, leave the lid open overnight to allow air to circulate and dry the tub. This helps prevent odors.

Cleaning the Dispenser Drawer

Detergent and fabric softener may build up in the dispenser drawer. Remove the drawer and inserts and check for buildup once or twice a month.Do not spray water inside the washer. Doing so may cause fire or electric shock.Turn off the washer, and unplug the power cord.Remove the drawer by pulling it straight out until it stops. Lift the front of the drawer upwards and pull it completely out.Remove the inserts from the two compartments.Clean the inserts and drawer with warm water.Use a soft cloth or brush to clean and remove any residue.Do not use soap when cleaning the drawer and inserts.Wipe off any moisture with a dry towel or cloth after cleaning.To clean the drawer opening, use a small, non-metal brush to clean the recess. Remove all residue from the upper and lower parts of the recess.Return the inserts to the proper compartments and replace the drawer.Set the drawer into the opening at an angle, then lower it and slide it into place.

Cleaning the Bleach Dispenser

Bleach may build up on the bleach dispenser. Check for buildup and clean the dispenser with warm water once or twice a month.

Cleaning the Water Inlet Filters

If the washer does not fill properly, an error message will appear on the display. The inlet valve filter screens could be clogged by hard water scale, sediment in the water supply, or other debris.The inlet screens protect the delicate parts of the inlet valve from being damaged by particles that could enter the valves with the water supply. Operating the washer with these filters removed could cause a valve to open continuously, resulting in flooding and/or property damage.Do not use the washer without the inlet filters. Doing so will cause leaks and malfunction.If you use the washer in an area with hard water, the inlet filter may clog due to lime buildup and require more frequent cleaning.Turn off the washer, and unplug the power cord.Turn off hot and cold water faucets.Unscrew the hot and cold water hoses from the back of the washer.Remove the filters from the water valves carefully.Use pliers to pull out the filters from the water valves.Remove foreign objects and soak the filters in white vinegar or a lime scale remover.If using a lime scale remover, follow the manufacturer’s instructions. Be careful not to damage the filters while cleaning them.Rinse filters thoroughly and press them back into place.Flush then reattach the water hoses.Before reattaching the water inlet hoses, flush them by running several gallons of water through them into a bucket or drain, preferably with the faucets wide open for maximum flow.An IE error message may blink on the display when the water pressure is low or an inlet filter is clogged with dirt. Clean the inlet filter.