UE
UNBALANCE ERROR
The load is too small.
Add additional items to allow the washer to balance the load.
Heavy articles are mixed with lighter items.
Always try to wash articles of somewhat similar weight to allow the washer to evenly distribute the weight of the load for spinning.
The load is out of balance.
Manually redistribute the load if articles have become tangled, preventing the automatic rebalancing from working properly.
IE
INLET ERROR
Water supply faucets are not fully open.
Make sure that the water faucets are fully open.
Water inlet hoses are kinked, pinched, or crushed.
Make sure that the hoses are not kinked, pinched or crushed behind or under the washer. Be careful when moving the washer during cleaning or maintenance.
Water inlet filters are clogged.
Clean the inlet filters. See MAINTENANCE.
Water supply pressure to faucet or house is too low.
Check another faucet in the house to make sure that household water pressure is adequate and flow is not restricted.
Disconnect the water inlet hoses from the washer and run a few gallons of water through the hoses to flush out any dirt.
If flow is too low, contact a plumber to have the water supply lines repaired.
Water supply connected with leak-limiting hoses.
The use of hoses designed to limit leaks is not recommended. Leak-limiting hoses can trip falsely and prevent the washer from filling.
The end of the drain hose is lower than 29.5 inches (75 cm) above the bottom of the washer.
Move the end of the drain hose so that it is higher than 29.5 inches (75 cm) above the bottom of the washer.
OE
WATER OUTLET ERROR
Drain hose is kinked, pinched, or clogged.
Make sure that the drain hose is free of clogs or kinks and is not pinched behind or under the washer.
The end of the drain hose is more than 96 inches (2.4 m) above the bottom of the washer.
Move the end of the drain hose so that it is lower than 96 inches (2.4 m).
dr
DRAIN FEATURE
Special drain feature
If the washer is paused during a cycle for more than 4 minutes, the cycle will be canceled and any water remaining in the tub will be drained.
This is not an error code. It indicates that the drain function is operating.
dE
LID ERROR
Lid is not closed properly.
Close the lid properly.
If the lid is closed and this error message is still displayed, call for service.
dL
LID LOCK ERROR
Lid is not locked properly.
Make sure that the lid is closed properly and press the Start/Pause button. You can hear the locking sound to lock the lid in the beginning of the cycle. The washer will not operate unless the lid is locked.
Make sure that nothing is caught under the lid, including shipping material or clothing.
Make sure that the latch mechanism is fully retracted.
If the lid is closed and this error message is still displayed, call for service.
LE1
FOREIGN OBJECT ERROR
Foreign objects such as coins, pins, clips, etc., are caught between the pulsator and the inner tub.
Turn the washer off then on again. Press the Spin button without selecting a cycle to drain and spin the load.
When the Spin cycle is completed, empty the tub and find and remove any objects caught in the pulsator.
Always check pockets, etc., before washing to prevent error codes or damage to the washer or clothing.
For some models, LE is displayed first, then the 1 is displayed.
vb
UNBALANCE DETECTION
The washer has detected an out of balance load.
This display is for your information only, and no action is required. If the washer detects a load that is too far out of balance to spin, it will display this code while it is attempting to rebalance the load. The washer will add water and try to redistribute the load automatically.
As a result, the cycle will take longer than initially estimated.
FE
OVERFLOW ERROR
Water level is too high due to a faulty water valve.
Close the water faucets, unplug the washer, and call for service.
PE
PRESSURE SENSOR ERROR
The water level sensor is not working correctly.
Close the water faucets, unplug the washer, and call for service.
LE
MOTOR LOCKED ERROR
A motor error has occurred.
Allow the washer to stand for 30 minutes and then restart the cycle.
If the error code is still displayed, call for service.
Eb
CLUTCH ERROR
Clutch error
Mechanical failure
Unplug the washer and call for service.