Removing the Left Refrigerator Door

The water supply is connected to the upper right part of the rear surface of the refrigerator. Remove the ring in the joint area. Hold the water supply connection and gently push the collet a to detach the water supply line as shown.Disassembling/Assembling the Water Linesb Collet c Tube d Insert line e ClipRemove the screw f from the hinge cover at the top of the refrigerator. Lift the hook (not visible), located at the bottom of the front side of the cover g with a flat-head screwdriver.Remove the cover and pull out the tube h. Disconnect all wire harnesses i. Unscrew the ground wire j.The number of wire harnesses may vary depending on the model.Rotate the hinge lever k counterclockwise. Lift the top hinge l free of the hinge lever latch m.When lifting the hinge free of the latch, be careful that the door does not fall forward.Lift the door from the middle hinge pin and remove the door.Place the door, inside facing up, on a nonscratching surface.

Removing the Right Refrigerator Door

Remove the top hinge cover screw a. Lift the hook (not visible), located at the bottom of the front side of the cover b, with a flat-head screwdriver.Detach all the wire harnesses c.The number of wire harnesses may vary depending on the model.Rotate the hinge lever d clockwise. Lift the top hinge e free of the hinge lever latch f.When lifting the hinge free of the latch, be careful that the door does not fall forward.Lift the door from the middle hinge pin and remove the door.Place the door, inside facing up, on a nonscratching surface.

Assembling the Right Refrigerator Door

Install the right-side door first.Make sure that the plastic sleeve is inserted in the bottom of the door. Lower the door onto the middle hinge pin as shown in the figure.Fit the hinge a over the hinge lever latch b and slot it into place. Rotate the lever c counterclockwise to secure the hinge.Connect the wire harnesses d.The number of wire harnesses may vary depending on the model.Place the cover e in its place. Insert and tighten the cover screw f .

Assembling the Left Refrigerator Door

Install the left refrigerator door after the right door is installed.Make sure that the plastic sleeve is inserted in the bottom of the door. Install the refrigerator door onto the middle hinge.Fit the hinge a over the hinge lever latch b and slot it into place. Rotate the lever c clockwise and fasten the hinge.Connect all the wire harnesses and the ground wire.The number of wire harnesses may vary depending on the model.Push the water supply tube into the hole on the top case and pull it through the backplate.Hold the water supply connection and gently push in the collet d to connect the water supply line as shown. Insert the tube at least 5/8 inch (15 mm) into the connector. Insert the clip on the joint to fasten the tube in place.Disassembling/Assembling the Water Linese Collet f Tube g Insert line h Clip Gently press the collet and insert the tube until only one line shows on the tube.Place the cover i in place. Insert and tighten the cover screw j.

Removing the CustomChill Drawer

Pull the drawer open to full extension. Remove the basket by lifting the basket from the rail system.Before removing the CustomChill drawer, it must be disconnected from the temperature control.Disconnect the wire harness connection at the end of the right rail by pressing on the tabs on either side. It may help to usea small, flat-blade screwdriver to apply pressure to the ends of the tabs on either side.Hold both sides of the door and lift it to remove it from the rail system.

Assembling the CustomChill Drawer

Grasp the door on each side and lower it into place on the rail system.Reconnect the wire harness to the connection at the end of the right rail by aligning the two ends and pushing them together until you hear a click. The tabs should snap back into place. Tug gently to make sure the connection is secure.If you do not reconnect the wire harness securely, the CustomChill drawer will not work properly.Pull the drawer open to full extension. Lower the basket onto the rail system.

Removing the Freezer Drawer

Use two or more people to remove and install the refrigerator doors and freezer drawer.Be careful of sharp hinges on both sides of the drawer.When you lay the drawer down, be careful not to damage the floor.Do not sit or stand on the freezer drawer.To prevent accidents, keep children and pets away from the drawer. Do not leave the drawer open. If the Durabase® storage bin is removed from the freezer drawer, there is sufficient space for a small child or pet to crawl inside.Pull the drawer open to full extension.Remove the top pullout drawer by first pulling the drawer open to full extension.On the left rail, use a flat blade screwdriver to push in on the tab to release the drawer from the rail, as shown below. Once the left side is loose, push the tab on the right side with your finger to release the drawer. Lift the front of the drawer up, then pull it straight out.Remove the middle drawer by pulling the drawer out to full extension. Lift the front of the drawer up, then pull it straight out.Remove the Durabase basket from the rails. Remove the screws from the rails at both ends.Grip both sides of the drawer and pull it up to remove it from the rails.Do not hold the handle when removing or replacing the drawer. The handle may come off, causing personal injury.Hold both rails and push them in simultaneously.

Assembling the Freezer Drawer

Pull out both rails simultaneously, until they are fully extended.Grasp the drawer on each side and hook the drawer supports into the rail tabs located on both sides.Do not hold the handle when removing or replacing the drawer. The handle may come off, causing personal injury.Lower the door into its final position and insert the screws in the rails on both sides.Insert the top pullout drawer into the frame, and push it back into place until you hear a click.Slightly tilt up the front of the middle drawer, insert the drawer into the frame, and push it back into place.Insert the lower basket in the rail assembly.