Top > MAINTENANCE > Cleaning > EasyClean

EasyClean

The EasyClean feature takes advantage of LG’s new enamel to help lift soils without harsh chemicals, and it runs using ONLY WATER for just 10 minutes in low temperatures to help loosen LIGHT soils before hand cleaning.

Your LG oven gives you the option of cleaning with LESS HEAT, LESS TIME, and virtually NO SMOKE OR FUMES. You can reduce energy use by cleaning light oven soils with the EasyClean feature instead of Pyrolysis.

Benefits of EasyClean

  • Helps loosen light soils before hand-cleaning.

  • EasyClean only uses water; no chemical cleaners.

  • Makes for a better Pyrolysis experience.

    • Delays the need for a Pyrolysis cycle

    • Minimizes smoke and odors

    • Can allow shorter Pyrolysis time

When to Use EasyClean

  • Example of oven soiling

    Case 1

    • Soil pattern: Small drops or spots

    • Types of soils: Cheese or other ingredients

    • Common food items that can soil your oven: Pizza

    Case 2

    • Soil pattern: Light splatter

    • Types of soils: Fat/grease

    • Common food items that can soil your oven: Steaks, grilled / Fish, grilled / Meat roasted at low temperatures

EasyClean Instruction Guide

Caution

  • The oven should be level to ensure that the bottom surface of the oven cavity is entirely covered by water at the beginning of the EasyClean cycle.

  • Do not open the oven door during the EasyClean cycle. Water will not get hot enough if the door is opened during the cycle.

  • Some surfaces may be hot after the EasyClean cycle. Wear rubber gloves while cleaning to prevent burns.

  • During the EasyClean cycle, the oven becomes hot enough to cause burns. Wait until the cycle is over before wiping the inside surface of the oven. Failure to do so may result in burns.

  • Avoid leaning or resting on the oven door glass while cleaning the oven cavity.

  • Do not use any steel scouring pads, abrasive pads or cleaners as these materials can permanently damage the oven surface.

  • Remove the baking tray, deep baking tray, wire grill, all cookware, aluminum foil, or any other material from the oven.

Note

  • Allow the oven to cool to room temperature before using the EasyClean cycle. If your oven cavity is above 65 ℃, the EasyClean cycle will not be activated until the oven cavity cools down.

  • For best results, use distilled or filtered water. Tap water may leave mineral deposits on the oven bottom.

  • Soil baked on through several cooking cycles will be more difficult to remove with the EasyClean cycle.

  1. Remove oven racks and accessories from the oven.

  2. Scrape off and remove any burnt-on debris with a plastic scraper.

    • Suggested plastic scrapers:

      • Hard plastic spatula

      • Plastic pan scraper

      • Plastic paint scraper

      • Old credit card

  3. Fill the tank to the Max line. Use softened, filtered water, if possible. Hard water may clog the steam generator more quickly with scale buildup.

  4. Press Cleaning in the Main Menu screen, then press EasyClean.

  5. Press the Start/Stop button on the control panel. The remaining time appears in the display.

  6. A tone will sound at the end of the 10 minutes cycle and Cleaning is finished appears in the display. Press the Start/Stop button on the display.

  7. After the cleaning cycle and during hand-cleaning, enough water should remain on the oven bottom to completely submerge all soils. Add water if necessary. Place a towel on the floor in front of the oven to capture any water that may spill out during hand-cleaning.

  8. Clean the oven cavity immediately after the EasyClean cycle by scrubbing with a wet, non-scratch scouring sponge or pad. (The scouring side will not scratch the finish.) Some water may spill into the bottom vents while cleaning, but it will be captured in a pan under the oven cavity and will not hurt the burner.

  9. Once the oven cavity is cleaned, wipe any excess water with a clean dry towel. Replace racks and any other accessories.

  10. If some light soils remain, repeat the above steps, making sure to thoroughly soak the soiled areas.

    • If stubborn soils remain after multiple EasyClean cycles, run the Pyrolysis cycle. Be sure that the oven cavity is empty of oven racks and other accessories, and that the oven cavity surface is dry before running the Pyrolysis cycle. Consult the Pyrolysis section of your owner’s manual for further details. (Model WSED7665B)

Note

  • The cavity gasket may be wet when the EasyClean cycle finishes. This is normal. Do not clean the gasket.

  • If mineral deposits remain on the oven bottom after cleaning, use a cloth or sponge soaked in vinegar to remove them.

  • Using commercial oven cleaners or bleach to clean the oven is not recommended. Instead, use a mild liquid cleanser with a pH value below 12.7 to avoid discoloring the enamel.