Cleaning Interval

Filter TypeWater WashingIntervala Air FilterO2 Weeksb PM1.0 Filter*1O6 Monthsc Deodorization Filter*1X6 MonthsThis filter is provided only when the air purifying front panel is installed.Never use water that is hotter than 40 7 when you clean the filters. Doing so may cause deformation or discolouration.Never use volatile substances when you clean the filters. Doing so may damage the surface of the appliance.The recommended cleaning intervals are based on 8 hours of daily use.If the filter is clogged with dust, the cooling/heating efficiency will drop.6 % of the electricity will be wasted.

Cleaning the Air Filter

Wear gloves during the work.Before cleaning or performing maintenance, disconnect the power supply and wait until the fan stops.When you remove the air filter, do not touch the metal parts of the indoor unit. Doing so may cause an injury.Do not bend the air filter, as it may break.Assemble the air filter properly to prevent dust and other substances from entering the product.Press the Knobs a on both sides and open the front grille.Press the Clips b on both sides and seperate the bottom of the air filter from the front grille.Remove the air filter.Press the Fixing Handle c and pull down the upper side of PM1.0 Filter d.Don't touch the PM1.0 Filter within 10 seconds after opening the front grille.Unless, it may cause an electric shock.Lift the PM1.0 Filter slightly and remove it from the appliance.Remove the Deodorization Filter e by pressing it up.Clean the air filter with a vacuum cleaner or wash it with lukewarm water and a mild detergent.Dry the filter in the shade.Soak the PM1.0 filter in enough water to submerge it and shake it several times to clean it.Clean the filter without disassembling it.If it is heavily soiled, soak it in lukewarm water with neutral detergent for 30 minutes, then rinse thoroughly with clean water.Dry in the shade for about a day.If you assemble the PM1.0 filter with moisture remaining, 7 beeps will sound.Do not use hot water over 40 \ or volatile liquids.Do not use acidic detergents such as citric acid.Drying with a hot air heater, such as a hair dryer or a heater, could damage or deform the filter.The inside of the filter is sharp, so do not rub or touch it directly.Do not wash the deodorization filter with water and dry for about 3 hours under weak sunlight or fluorescent light.Washing the filter with water could damage or deform it.Insert the Deodorization Filter e into the PM1.0 Filter by pressing it down.Mount PM1.0 Filter d on the hooks.Push up the upper side of PM1.0 Filter and fix to the appliance.Insert the hooks on the upper side of the air filter into the holes.Insert the clips into the hooking holes on the bottom of front grile.Close up the front grille to the appliance.Fix the upper side of the front grille by pressing the knobs.Press the centre of the left and right sides once.

Cleaning the PM1.0 Sensor

This process is applicable only when the air purifying front panel is installed.PM1.0 Sensor is only included with air purifying front panel.It is recommended to clean the PM1.0 sensor every 6 months.(assuming 8 hours of daily use)Cleaning interval is set period assuming that 8 hours of daily use.Turn off the power to the appliance before work.Be careful not to drop the product when removing the PM1.0 Sensor corner cover.Be careful of falling accidents when cleaning the PM1.0 sensor.Remove the dust sensor corner cover a on the front panel.After opening the PM1.0 sensor cover b, remove the rubber cover c.Wipe off any dust adhering to the lens using a cotton swab slightly moistened with water. Then wipe again with a dry cotton swab to remove moisture.After inserting the rubber cover c, assemble the PM1.0 sensor cover b.Assemble the dust sensor corner cover a on the front panel.The dust sensor shown below does not require cleaning.The sensor cover is affixed to the sensor with the screw.

Cleaning the Air Filter(The Lift Grille Type)

Wear gloves during the work.Before cleaning or performing maintenance, disconnect the power supply and wait until the fan stops.When you remove the air filter, do not touch the metal parts of the indoor unit. Doing so may cause an injury.Do not bend the air filter, as it may break.Assemble the air filter properly to prevent dust and other substances from entering the product. Removing the FilterPress the K (down) button on the wireless remote control for the lift grille. Do not ride on the lift grille when it is moving up or down.The lift grille may get damaged, malfunction, or fall and cause injury. The length of the lift grille descending from the product is as follows.Press the K button on the remote control once to descend to the default descent length of 2m.Press the K button on the remote control once more to descend to the maximum descent length of 3.7m.The minimum descent length of the lift grille is 1m.The lift grille automatically stops if it interferes with any object or touches the floor whilst coming down.To change the default lowering length of the lift grille to a length other than 2m, press the ^ button on the remote control five times in succession when the lift grille is in the desired position.The position in which you press the ^ button on the remote control five times in succession is set as the basic lowering length of the lift grille.The default descent length can be set in the range of 1m to 3.7m.Press the fixed hook and lift the air filter. Remove the air filter.Pull out the Deodorization Filter a to separate it from the PM1.0 Filter b.Don't touch the PM1.0 Filter within 10 seconds after opening the front grille.Unless, it may cause an electric shock. Cleaning the Deodorization Filter and the PM1.0 FilterDeodorization FilterDo not wash the deodorization filter with water and dry for about 3 hours under weak sunlight or fluorescent light.PM1.0 FilterSoak the PM1.0 filter in enough water to submerge it and shake it several times to clean it.If it is heavily soiled, soak it in lukewarm water with neutral detergent for 30 minutes, then rinse thoroughly with clean water.Dry in the shade for about a day.If you assemble the PM1.0 filter with moisture remaining, 7 beeps will sound.Do not use hot water over 40 7 or volatile liquids.Do not use acidic detergents such as citric acid.Drying with a hot air heater, such as a hair dryer or a heater, could damage or deform the filter.The inside of the filter is sharp, so do not rub or touch it directly.Insert the Deodorization Filter a into the PM1.0 Filter b.Cleaning the Air FilterRemove the air filter mounted on the front grille. Clean the filter with a vacuum cleaner or a soft brush. If it is heavily contaminated, wash it with lukewarm water mixed with a neutral detergent. Dry the filter in a well-ventilated, shaded area. Insert the air filter. Assemble the air filter. Use the wireless remote control for the lift grille to raise the lift grille. If you open the front grille during installation or maintenance, the inner grill may not engage. In that case, the main circuit breaker must be turned on again for the air conditioner to operate normally. The lift grille will automatically stop and lock when it is coupled with the indoor unit.